Knife Gate Valves are widely used in the areas of Pulp, Paper, Water, Waste Water, Sewage, Mining, Slurry & Power Generations. Vatac offers Knife Gate Valves in both Resilient & Metal Seated, Flged, Wafer and Full Lugged Types. Knife Gate valves is similar to a gate valve, but usually more compact. Often used for slurries or powders on/off control.

Vatac Cast & Ductile Iron butterfly valves in both Con-centric and Eccentric Structures, in wafer, flanged & Fully Lugged Designs. Bubble-tight shut off for all items. Meets or exceeds updated Intl Stds of ASME, AWWA & DIN

Vatac Resilient Seated Gate Valves are available in Both Rising Stem & Non-rising Stem, standards compliance to DIN 3202 F4 or F5, AWWA C509, ASME, EN or BS. FBE Coated inside and outside to a maximise service life.

Vatac Metal Seated Gate Valves are with compact design to most updated int'l standards of DIN 3202, AWWA, AS or ASME. Suitable for use with drinking water and waste water in above-ground and under-ground applications.

investment casting ball valve, v port ball valve, thread ball valve, direct mounted ball valve, cast ball valve, forged ball valve, Cast Iron Ball Valves manufactured by Vatac are available in both One and Two piece body, ends connections in thread, weld and flange.

Vatac globe valves are offered in both Straight Through and Angle Pattens, Optional SDNR Structure. These items are typically used for the commercial and industrial services of hot and cold water, HVAC, steam, gas and other utilities.

Non slam check valve, Nozzle Check Valve, Axial Flow Check Valve, Check Valves offerd by Vatac are not limited to conventional types of Swing & Piston, also in Dual Plate, Non-slam and other specials. Vatac Check Valves are designed and manufactured to the most updated int’l standards.

Vatac Strainers are mostly offered in Y Types. Designed and manfuactured to ASME B16.34 or DIN 3202, Standard Trims in Stainless Steel. Ends Connections in Flanged, Threaded or Welded, Classes up to 150#.

Vatac quarter-turn valves are equipped with a position indicator marked at 10 degree increments and an open position memory stop that can be used for balancing applications. Valves 3" through 8" are available with lever actuators. Geared actuators are recommended on 6" and larger valves. It is also recommended that valves installed in pipelines with high velocity or where water hammer conditions can be caused by sudden valve shut-off that geared actuators be installed. Lever actuators can only be used for pressure ratings of 100 psi maximum and 25 psi in the reverse flow condition. Vatac Eccentric Plug valves are available in sizes ranging from 3" - 24".

Vatac diaphragm valves are engineered for tough work environments in the chemical processing, water treatment, pollution control, food and beverage, mining, pharmaceutical, pulp and paper, power generation industries.

Vatac air valves has been contributing to the improvement of the efficiency of the water system for over 20 years. The Vatac Air Release Valves are constructed from rugged castings that are machined to exacting specifications. These bodies either have both threaded ends to International standards ASME or DIN, or with drilled flanges that are in accordance with ASME B16.1. Alternatively to EN, DIN, BS or JIS Standards

Vatac Pinch Valves meet Industry Standard face-to-face dimensions accepted by all engineering/design companies, thus allowing interchangeability with other valves built to the same industry standards.

Vatac Foot valves are Used on the end of a suction line to stop fluids in the line emptying when the pump is turned off, thus eliminating the need to prime your pump at start up. Available in a broad line of body materials in cast iron, ductile iron, carbon and stainless steel.

The Vatac Rubber Flexible Joints (Rubber Joint) are ideal in heating and air conditioning systems, where low initial cost and maximum reliability are a must. The Vatac connectors have EPDM cover, providing excellent resistance to sunlight, ozone, oxidation and is resistant to damage from dropping oil. These items are with a EPDM tube, which is good for hot and cold-water service & mild chemicals.

Vatac offers a broad line of cast iron fittings including, but not limited to Cast iron Flange, Adpter, Coupling, Dismantling and Expansion Joint, Pipe fittings for DI and PVC Pipes. Sizes from 1/2" to 80".